Gas line repair & installation in Charlotte, NC
Leaking gas fitting, a new range that needs a line, or a standby generator waiting on a hookup? We repair, extend and install household gas piping across the Charlotte metro, pull the Mecklenburg permit, pressure test every line and give you a flat price up front.
If you smell gas, the house comes first

Rotten eggs, a hiss near the water heater or behind the dryer, a strip of dead grass over the yard line. Any one of those is enough. Get everybody out, pets included, and leave the lights and switches exactly as they are. Don't call from inside. Once you're across the street, call 911 or the Piedmont Natural Gas emergency number. Piedmont comes out free, finds the leak and shuts off or red-tags whatever is unsafe.
A carbon monoxide and natural gas combo detector near the furnace and water heater is cheap insurance, especially when those appliances sit in a closet or crawl space where a small leak can build up before anyone notices.
Then call us. Piedmont owns the meter and the service line up to it. Everything past the meter, the piping through your crawl space, walls and attic, belongs to you, and that is the part we fix. We'll replace the bad fitting, valve or section, test the system and get the gas turned back on. Our gas smell checklist is worth reading once before you ever need it.
Black iron, CSST, and what we find in Charlotte crawl spaces

Most older Charlotte homes, the 1950s ranches in Cotswold and East Charlotte and plenty of 80s two-stories, are piped in black iron. It's threaded steel. It lasts a very long time indoors, and when it leaks it's almost always at a joint, a union or an old appliance valve, not the pipe itself. In a damp crawl space, though, we do see surface rust on runs that sat against the dirt for forty years.
Newer homes and a lot of remodels use CSST, the flexible yellow-jacketed stainless tubing. It's fast to run and has fewer joints, which is good. The catch is lightning. CSST has to be bonded to the home's electrical grounding system, and we still find installs where nobody did it. If you have yellow tubing and no bonding clamp near where it enters the house, we'd fix that before anything else. On new work we use whichever material fits the run, and we'll tell you why.
Running a new line for a range, dryer, generator or fire pit


Most of our install calls start with someone swapping an electric range for gas, adding a gas dryer, or going tankless. Out back it's outdoor kitchens, built-in grills, fire pits and standby generators. Outdoor lines get trenched and run in coated pipe or polyethylene rated for burial, with a shutoff where you can reach it.
Sizing is where amateur jobs go wrong. Every appliance pulls a set number of BTUs and the piping has to carry all of them at once. A whole-house generator or a tankless heater can use more gas than everything else in the house combined, so tapping off the nearest pipe doesn't work. We add up the full load, check the pipe size back to the meter, and if the meter itself is too small we tell you before we start so you can request a meter upgrade from Piedmont. Here's the longer write-up on gas line installation cost.
Pressure tests, permits and the county inspector

Gas work in Mecklenburg County needs a permit, and we pull it. New or repaired piping gets capped and pressurized with air, and a gauge has to hold steady for the test period with no drop. The inspector looks at the gauge, the materials, the supports and the bonding, then signs off so the gas can go back on. Surrounding counties like Union, Gaston and York run their own inspections, and we handle those too.
Honestly, the test is the whole point. A slow leak at a threaded joint inside a wall is the one you never smell until it's a problem. If someone quotes you gas work with no permit, that's the step they're leaving out. More on that in our permits guide.
Typical gas line prices around Charlotte
Repairs are usually the smaller tickets. Fixing a leaking fitting or connector runs about $150 to $400, a new appliance shutoff valve or flex connector $150 to $350, and repairing or replacing a section of line $400 to $800. A pressure test of the whole system on its own is around $150 to $350.
New lines depend mostly on distance and how many floors and turns the pipe has to make:
- Short run to a nearby range or dryer: $350 to $800
- Longer run across the house: $800 to $1,800
- New line from the meter, or a standby generator hookup: $1,200 to $3,500
- Gas upgrade for a tankless water heater: $500 to $1,500 on top of the unit
We look at the job first, then give you one flat price that already includes the permit and inspection.
Gas line repair & installation questions
Who do I call first if I smell gas, a plumber or the gas company?
The gas company, every time. Get outside, then call 911 or Piedmont Natural Gas from a safe distance. They respond around the clock at no charge and will shut off or red-tag what's leaking. Once they've made it safe, call us to repair the piping on your side of the meter and get the system tested so the gas can go back on.
Can a plumber install a gas line in North Carolina?
Yes. In North Carolina, gas piping inside and around a home is done by a licensed plumbing or fuel piping contractor under a permit. We run lines to ranges, dryers, water heaters, fireplaces, grills and generators, test them, and schedule the county inspection. Piedmont Natural Gas handles the meter and the service line up to it.
Is CSST gas line safe?
CSST is safe when it is installed and bonded correctly. The yellow tubing needs a bonding connection to the home's electrical grounding system so a nearby lightning strike can't arc through it. Many older installs were never bonded. Adding a bonding clamp and conductor is a small job, and we check for it any time we see CSST in a Charlotte home.
How long does it take to run a gas line for a new stove?
A straight run to a kitchen range from a crawl space or basement is usually done in a few hours, including the pressure test. The gas can't go into service until the county inspector signs off, which is typically a day or two depending on the inspection schedule. Longer runs, attic routing or a generator line can take a full day or more.
How much does it cost to run a gas line for a generator in Charlotte?
Most standby generator gas hookups fall between $1,200 and $3,500. Distance from the meter matters most, along with trenching and whether the meter is big enough to carry the generator plus your furnace and water heater. If Piedmont needs to upsize the meter, we tell you before work starts so the timing lines up with your electrician.
What Charlotte Homeowners Say
We're new to Charlotte, and we're building our reputation the only honest way there is: one job at a time, done right, at the price we quoted. Every Hornets Nest job comes with flat-rate pricing, a licensed and insured crew, and a real person answering the phone 24/7.
Need a gas line run or repaired?
Call and tell us what the line needs to feed, and we'll give you a flat price that includes the permit and the test.
๐ Call (704) 419-7362